不同区域原状黄土颗粒和孔隙特征分析          下载免费PDF全文

胡海军  周康  骆亚生  胡全  赵文鹏  张志毅 《地震工程学报》2015,37(S1):22-25

研究不同区域黄土颗粒和孔隙大小、形状和排列的定量差异,针对甘肃兰州、陕西西安和山西运城的原状黄土的电镜照片进行定量分析。首先应用Autocad描绘获得颗粒和孔隙的边界,拉开各对象后填充,然后导入到图像分析软件中获得各对象的长轴,短轴、周长、面积和长轴方向角;其次应用得到的参数计算反映对象大小、形状和定向排列的定量参数;最后比较不同区域原状黄土中颗粒和孔隙的定量参数差异。结果表明:甘肃兰州黄土颗粒的平均直径最大,形状最偏离圆形,三个区域颗粒排布在空间分布均匀;甘肃兰州黄土的孔隙平均直径与陕西西安的接近,形状更偏离圆形;颗粒的平均直径接近于孔隙的平均直径,颗粒形状更接近于圆形。  相似文献   

新疆伊犁河谷黄土滑坡冻融失稳机理研究     

朱赛楠  殷跃平  王文沛  魏云杰  邵海  黄喆  庄茂国  石爱军 《地球学报》2019,40(2):339-349

伊犁河谷地处中国天山山脉西段,属于典型的季节性冻土区,季节性冻融作用对斜坡稳定性影响强烈。本文以皮里青河"3.24"滑坡为例,通过现场详细调查、多期遥感影像动态比对、数值模拟等方法,研究了黄土滑坡冻融失稳机理与滑坡运动特征,得到以下几点认识:(1)滑坡失稳与水密切相关,一方面是地表水侵蚀作用,另一方面是地下水的冻融作用;(2)根据变形特征,将滑坡失稳过程分为坡脚侵蚀、冻结滞水和冻融循环破坏三个阶段,模拟结果表明,地下水水位上升导致孔隙水压力增大是滑坡冻融失稳的主要原因;(3)DAN-W数值模拟软件的Voellmy模型和Frictional模型可较好地模拟滑坡的运动堆积过程,模拟结果显示,滑坡历时12.8 s,最大运动速度17.7 m/s,平均堆积厚度4.9 m,运动距离139 m。本研究为伊犁河谷地区黄土冻融滑坡的早期识别与风险评估提供了重要的技术支撑。  相似文献   

东乡县湿陷性黄土回填碾压的施工控制措施          下载免费PDF全文

燕强珍  梁小鹏  杨中明  彭博 《甘肃地质》2017,26(4):70-76

针对东乡县湿陷性黄土回填碾压质量要求及控制工序,用运碾压厚度试验、含水率试验、碾压遍数试验、碾压速度试验等,从湿陷性黄土回填碾压的两个控制工序,即黄土回填和黄土碾压出发,全面系统的分析了压实度影响因素并提出了施工控制措施。研究表明,在相同压实条件下,适宜的回填厚度有益提高压实度质量和效益;确定最佳含水率后,在施工中不影响施工质量的前提下,相对扩大土的含水率控制范围,既能达到整体压实稳定,又能加快施工进度;在相同的回填条件下,同一深度的压实度随压实机械功能增大,压实度越高;在相同压实功能条件下,同一深度范围内碾压遍数越多,压实度越高;增加压实功能的办法提高土基强度的效果有一定限度,吨位增加到一定限度以上,效果提高愈为缓慢;碾压速度加倍时,碾压遍数相应加倍,应针对具体碾压材料层和所用压路机,通过铺筑试验区域选择合适的碾压速度。  相似文献   

兰州九州重塑黄土的抗拉变形破坏机理   总被引：3，自引：2，他引：1  

吴旭阳  梁庆国  牛富俊  李国玉 《冰川冻土》2017,39(4):842-849

通过对不同干密度及含水量的重塑黄土进行室内抗拉强度试验,探究轴向压裂法致使试样破坏的机理及一般规律。结果表明,黄土的抗拉变形破坏可分为4种类型：I类,高干密度低含水量（干密度大于1.65 g·cm^-3,含水量小于15%）,抗拉强度介于8~12 kPa;Ⅱ类,低干密度低含水量（干密度小于1.60 g·cm^-3,含水量小于15%）,抗拉强度介于4~8 kPa;Ⅲ类,高干密度高含水量（干密度大于1.65 g·cm^-3,含水量大于17%）,抗拉强度介于4~8 kPa;IV类,低干密度高含水量（干密度小于1.60 g·cm^-3,含水量大于17%）,抗拉强度介于3~4 kPa。I类、Ⅱ类破坏类型属于脆性破坏,Ⅲ类、IV类属于塑性破坏。重塑黄土抵抗变形最弱的含水量为15%。通过对比分析黄土、普通黄黏土、红黏土及膨胀土的抗拉强度发现,在最优含水量处,不同干密度下黄土的抗拉强度均最小。黏性土的持水能力远超过黄土。黏土及膨胀土的抗拉强度均在最优含水量处达到最大值,而黄土的抗拉强度随着含水量的增加持续减小。研究结果对黄土强度特性的理解具有一定的参考意义。  相似文献   

基于SRTM DEM的地形起伏度对天水市黄土滑坡的影响分析   总被引：2，自引：0，他引：2  

宿星  魏万鸿  郭万钦  王思源  王国亚  吴玮江  叶伟林 《冰川冻土》2017,39(3):616-622

以天水市辖区30 m分辨率的SRTM DEM数据为基础,首先利用GIS空间分析模块中邻域统计分析法,依次选取2×2、3×3、4×4、…、28×28、29×29、30×30共29个矩形邻域分析窗口,运用均值变点分析法进行最佳计算单元的计算分析。结果表明：12×12的网格大小（12.96×10⁴ m²）为曲线突变的拐点,作为曲线由陡变缓的阈值,确定12×12的网格大小（12.96×10⁴ m²）为研究区地形起伏度计算的最佳单元,生成研究区地形起伏度分级图。进而采用确定性系数法（CF）、证据权法、信息量法和条件概率法对研究区发育的黄土滑坡灾害与地形起伏度之间的相关关系进行了定量分析。研究结果表明,区内地形起伏度影响因子层中地形起伏度60~120 m的分级因子层为黄土滑坡灾害的易发因子层,而其中60~90 m区间的值最大,为黄土滑坡灾害的优势因子区间,对滑坡的响应最敏感。  相似文献   

A call for Australian loess: discussion and commentary     

Ian Smalley 《Area》2008,40(1):131-134

A study of loess in Australia brings the idea of 'desert' loess back into view. Production of particles in deserts still presents problems, but deserts do make adequate storage regions for loess particles – usually produced in adjacent mountains. Straightforward for Central Asia or China (a particle source in High Asia and convenient deserts en route to eventual deposition), but the Sahara and Australian deserts traditionally present problems. If loess material is allowed to be silt-sized clay agglomerate particles as well as the usual clastic primary minerals, then loess in Australia seems reasonable. Loess acquires its remarkable loessic qualities via aeolian deposition – the nature of the particles is perhaps of lesser importance. A more generalised approach to airborne sediments might be attempted, with two major types of suspension material recognised: large dust (maybe coarse and very coarse silt, say 20–60 µm, or perhaps 4–6 phi) and small dust (fine and very fine silt, 2–8 µm, 7–9 phi). Loess is made from large dust.  相似文献   

封顶覆盖黄土气体渗透特性测试及填埋气一维运移分析     

杨益彪  詹良通  王顺玉  陈云敏  赵云飞 《岩土力学》2015,36(7):1973-1980

黄土在我国西北地区广泛分布,是当地垃圾填埋场封顶覆盖层的主要材料,该材料的气体渗透特性直接影响了覆盖层对填埋气释放的控制效果。利用渗析技术和自制的气体渗透系数测量装置,模拟和测试了干湿气象条件下覆盖黄土服役含水率变化及其对气体渗透系数的影响,并建立填埋气在垃圾体和覆盖层中的一维稳态运移模型,分析了覆盖层气体渗透系数和抽气速率对填埋气释放控制效果的影响。研究结果表明：渗析技术能有效模拟覆盖黄土服役含水率的变化,压实黄土试样的气体渗透系数介于10-17～10-12 m2量级,随服役含水率的增加而降低,且对于压实度比较高的黄土降低得更加明显;覆盖层底部的填埋气压随气体渗透系数的减小而增大,通过覆盖层下部的气体扩散层负压抽气等措施,可有效减小覆盖层底部气压和填埋气的释放量。  相似文献   

西安地区地裂缝带Q3原状黄土流变特性试验研究     

邓亚虹  李丽  慕焕东  王鹏  李飞霞 《岩土力学》2015,36(7):1847-1855

汾渭盆地是我国乃至世界上地裂缝最为发育、灾害最为严重的地区。考虑在漫长的地质历史过程中黄土的流变特性对地裂缝破裂扩展模式的影响,采用分级循环加卸载方式,对西安地区长安地裂缝（fc1）带Q3原状黄土进行了不同围压下的固结不排水三轴流变特性试验,得到了地裂缝带Q3原状黄土的蠕变加、卸载曲线和应变速率与时间关系曲线。试验结果表明,不同围压下地裂缝带Q3原状黄土表现为低应力下为减速蠕变,高应力下为减速蠕变和等速蠕变的特征。并基于统一流变力学模型理论,建立了适用于西安地区地裂缝带Q3原状黄土的三维蠕变本构模型,获得了相应的本构模型参数。该成果为研究隐伏地裂缝破裂扩展模式及其力学机制奠定了基础。  相似文献   

Chronology of the Holocene loess-paleosol section and its deposition and pedogenesis on the south of Chinese Loess Plateau     

JIA Yaofeng  HUANG Chunchang  PANG Jiangli  NIU Junjie 《地理学报》2008,18(4):425-442

Optically stimulated luminescence (OSL) dating for polymineral fine-grained loess samples, collected in Laoguantai (LGT) section on the south of the Chinese Loess Plateau, was made by application of single-aliquot regenerative-dose (SAR) protocol. A ‘Double-SAR’ procedure in which aliquots are subjected to both infrared (IR) and blue stimulations was used, and two sets of equivalent dose (De) determinations were produced and assumed to relate predominantly to feldspathic and quartz fine grain populations respectively. The OSL ages estimated from IRSL signals are smaller than those estimated from [post-IR] OSL signals due to the anomalous fading of feldspar IR signals, based on fading experiment. The young ages of the samples near ground surface may be originated from the post-depositional disturbance by the intensifying humanity’s cultivation since 3.0 ka BP in the Guanzhong Basin, south of the Chinese Loess Plateau. Based on OSL dating, as well as field observations and stratigraphic correlation, we determine the chronology of the LGT loess-paleosol sequence. In combination with climate proxy records, it is indicated that aeolian loess deposition and pedogenesis underwent polyphase changes during the Holocene, likely to have been driven by shifts in the East Asian monsoon. This suggests that aeolian loess deposition is episodic and highly variable, with contributions from non-aeolian processes such as alluvial deposition found in the area.  相似文献   

Chemical weathering intensity and element migration features of the Xiashu loess profile in Zhenjiang, Jiangsu Province     

CHEN Yingyong  LI Xusheng  HAN Zhiyong  YANG Shouye  WANG Yongbo  YANG Dayuan 《地理学报》2008,18(3):341-352

The chemical weathering intensity and element migration features of the Xiashu loess profile in Zhenjiang are studied in this paper. (1) The Xiashu loess profile underwent moderate chemical weathering. It seems that the precipitation is a more important factor than the temperature in controlling the process of the chemical weathering. (2) The major elements such as Si, K, Na, Ca, Mg, Mn and P were migrated and leached, while the elements Fe and Ti were slightly enriched. The migration features of the major elements reveal that the Xiashu loess finished the primary process of chemical weathering characterized by leaching of Ca and Na, and almost reached the secondary process characterized by leaching of K. Except the elements Sr and Ga, other trace elements such as Th, Ba, Cu, Zn, Co, Ni, Cr and V were enriched. It might be caused by both the biogeochemical process and the adsorption of trace elements by clay mineral and organic materials. (3) The difference of element migration down the Xiashu loess profile reveals that the climate was warm and wet at the early-middle stage of the middle Pleistocene. At the end of the middle Pleistocene, it became dry and cool. At the early stage of the Late Pleistocene, the paleoclimate became warm and wet again. As a whole, the paleoclimate generally became drier and cooler in this region from the beginning of the middle Pleistocene.  相似文献